收藏本站
NCP3488
Safety Timer and Overlap Protection Circuit
It is very important that MOSFETs in a synchronous buck
regulator do not both conduct at the same time. Excessive
shoot ? through or cross conduction can damage the
MOSFETs, and even a small amount of cross conduction
will cause a decrease in the power conversion efficiency.
The NCP3488 prevents cross conduction by monitoring
the status of the external MOSFETs and applying the
appropriate amount of “dead ? time” or the time between the
turn off of one MOSFET and the turn on of the other
MOSFET.
When the PWM input pin goes high, DRVL will go low
after a propagation delay (tpdlDRVL). The time it takes for
the low ? side MOSFET to turn off (tfDRVL) is dependent on
the total charge on the low ? side MOSFET gate. The
NCP3488 monitors the gate voltage of both MOSFETs and
the switchnode voltage to determine the conduction status of
the MOSFETs. Once the low ? side MOSFET is turned off an
internal timer will delay (tpdhDRVH) the turn on of the
Input Pins
The PWM input and the Output Disable pins of the
NCP3488 have internal protection for Electro Static
Discharge (ESD), but in normal operation they present a
relatively high input impedance. If the PWM controller does
not have internal pull ? down resistors, they should be added
externally to ensure that the driver outputs do not go high
before the controller has reached its under voltage lockout
threshold. The NCP5388 controller does include a passive
internal pull ? down resistor on the drive ? on output pin.
Bootstrap Circuit
The bootstrap circuit uses a charge storage capacitor
(C BST ) and the internal (or an external) diode. Selection of
these components can be done after the high ? side MOSFET
has been chosen. The bootstrap capacitor must have a
voltage rating that is able to withstand twice the maximum
supply voltage. A minimum 50 V rating is recommended.
The capacitance is determined using the following equation:
high ? side MOSFET
Likewise, when the PWM input pin goes low, DRVH will
CBST +
QGATE
D VBST
go low after the propagation delay (tpdDRVH). The time to
turn off the high ? side MOSFET (tfDRVH) is dependent on
the total gate charge of the high ? side MOSFET. A timer will
be triggered once the high ? side MOSFET has stopped
conducting, to delay (tpdhDRVL) the turn on of the
low ? side MOSFET
Power Supply Decoupling
The NCP3488 can source and sink relatively large
currents to the gate pins of the external MOSFETs. In order
to maintain a constant and stable supply voltage (V CC ) a low
ESR capacitor should be placed near the power and ground
pins. A 1 m F to 4.7 m F multi layer ceramic capacitor (MLCC)
is usually sufficient.
12 V
NCP3488
where Q GATE is the total gate charge of the high ? side
MOSFET, and D V BST is the voltage droop allowed on the
high ? side MOSFET drive. For example, a NTD60N03 has
a total gate charge of about 30 nC. For an allowed droop of
300 mV, the required bootstrap capacitance is 100 nF. A
good quality ceramic capacitor should be used.
The bootstrap diode must be rated to withstand the
maximum supply voltage plus any peak ringing voltages
that may be present on SW. The average forward current can
be estimated by:
IF(AVG) + QGATE fMAX
where f MAX is the maximum switching frequency of the
controller. The peak surge current rating should be checked
in ? circuit, since this is dependent on the source impedance
of the 12 V supply and the ESR of CBST.
12 V
Output Enable
PWM in
4
3
2
Vcc
OD
IN
BST
DRVH
SW
DRVL
PGND
1
8
7
5
6
Vout
Figure 4. NCP3488 Example Circuit
http://onsemi.com
6
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP5007SNT1 IC LED DRIVR WHT COMPACT 5TSOP
NCP5008DMR2 IC LED DRVR WHT BCKLT 10MICROSMD
NCP5010FCT1G IC LED DRVR WHT BCKLT 8-FLIPCHIP
NCP5021MUTXG IC WHITE LED DVR HV AMB 16-UQFN
NCP5050MTTXG IC LED DRIVR PHOTO FLASH 10-WDFN
NCP5111DR2G IC DRIVER HI/LOW SIDE HV 8-SOIC
NCP5304DR2G IC DRIVER HI/LOW SIDE HV 8-SOIC
NCP5355DG IC DRVR SYNC BUCK MOSF 12A 8SOIC
相关代理商/技术参数
NCP348AEMTTBG 功能描述:监控电路 POS OVERVLTG PROTECT CONTROLLER RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
NCP348AEMTTBG-CUT TAPE 制造商:ON 功能描述:NCP348AE Series 6.4 V Threshold 28 V Positive Overvoltage Protection Controller
NCP348AEMTTXG 功能描述:监控电路 POS OVERVLTG PROTECT CONTROLLER RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
NCP348AEMUTBG 功能描述:监控电路 POSTIVE OVP PRTCTION RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
NCP348GEVB 功能描述:电源管理IC开发工具 EVALUATION BRD DEV RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP348GEVB 制造商:ON Semiconductor 功能描述:Positive Overvoltage Protection Controll
NCP348MTTBG 功能描述:监控电路 OVER VLTG PROTECTION RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
NCP348MTTXG 功能描述:监控电路 POS OVR PROTCT CNTRL RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel